Showing posts with label mast raising system. Show all posts
Showing posts with label mast raising system. Show all posts

Saturday, July 21, 2012

Door County - Day Four



The beautiful scenery at Peninsula State Park
Our sailing partners pulled out early so we had the day to play on own. After we helped them put their boat on the trailer, we headed back to Wrinkles and motored out through the channel.

The winds were lighter, but looked promising. We kept the reef in the main and went to full headsail until we figured out what the winds were going to do. We didn't really have a plan on where we wanted to go and since the winds would let us, we headed south toward Fish Creek and the Strawberry Islands. We had sailed into Fish Creek from Egg Harbor before, but this would be the first time we had come in from the North. There are small islands and numerous shoals in this are which required us to hone our dead reckoning skills while allowing us to play with the iNavX software on the the iPad.We also had our paper charts along for reference.  Mike preferred the iNavX and Brenda preferred the old fashioned paper method.

Screen shot from iNavX on iPad
The winds were dying so we switched back and forth from sailing to motor sailing. We passed close by the Number 6 bell buoy. We haven't sailed close to one of these kinds of buoys before so we had to stop, listen and video.You can see the shoals in the background of the picture below.

We turned to the West following the shoals toward Chambers Island enjoying the beautiful scenery. To our naked eye we could see what appeared to be white posts sticking up in the middle of the water. It looked like a dilapidated picket fence. Through our binoculars we could see that this was actually the birds standing ankle deep on rocks in the water. It was a pretty cool sight, but if someone wasn't using their charts, they could very easily take the bottom out of their boat! So take your charts with you if you are going to sail this area folks!

The shoals in the Strawberry Islands
We sailed between Chambers Island and the Strawberry Islands which consist of Adventure Island, Jack Island and Pirate Island. Two islands even had what appeared to be private residences. How cool would that be??!!

Lots of room to sail here!
We were zipping right along and then the winds died again. We bobbed along for awhile (thank goodness for the bimini). When the wind cooperated, we played around a little bit with the loose-footed set up on the mainsail. It seems like it should offer better sail shape. We are anxious to get our new sail to see what a difference it makes.

Beautiful view during one of the calms
It was hard to motor in, but after six hours of sailing and about 20 nm, we were ready to get Wrinkles loaded up and start our four hour drive home.

Motoring into Eagle Harbor and our marina
When we got back to the dock, there were boats coming and going. There was no holding area there, so we ended up just killing time in the three foot deep channel waiting for a gap to open up.  The mast-raising system continues to serve us well and draw a crowd of observers. Tear down went quickly and easily, but it was still hot. We took advantage of the showers at the marina before we hit the road.

Now you can see why we look forward to our Door County sailing trips. There is beautiful scenery, nice marinas, great sailing grounds, interesting boats to see, places to shop and eat, and maybe a bar or two. We will definitely return again next year.

Tuesday, April 17, 2012

Mast Raising System

One of the biggest drawbacks to trailer sailing is the fact that the mast must be raised and lowered every time you sail.  On our previous sailboats the mast was relatively easy to manually raise with one or two people.  The Com-Pac 23 has a bit heavier mast which can be muscled up by a two or three people, but it isn't something you really want to be involved in. 

So, I decided to see what other sailors with similarly sized sailboats were using to assist them in raising their masts.  There are some factory supplied systems and even one or two aftermarket units that I found while searching the web.  A good friend of mine had a Hunter 22 and he had devised a version of the gin pole system.  After watching him install the gin pole, raise the mast and remove the gin pole I felt it was too much work.  I hadn't found any good descriptions or videos of a permanently mounted post system (although I have read about others building such a system) so I took what I liked of several systems and used some spare metal , used line, a few hardware pieces and a cheap winch to make my own version.

I had a couple of guidelines in my head of what the system should be like.  First it should be CHEAP!,  Second it should be simple to attach and operate. Third it should not require much time to use.  Fourth it should support the mast from side to side during its entire travel from horizontal to vertical.

Cheap - about $20 worth of simple hardware including a steel pulley and $25 for a winch
Simplicity - well I can operate it which proves it is simple
Time of use - the bridles take about 2-3 minutes to attach and the permanently attached post saves time
Support - the bridles maintain the plane of the mast even if you stop at any time during the raising/lowering

How to use;

RAISING
Attach the two bridles using some kind of quick snap shackles and attach the main halyard to them.
Tension the main halyard and cleat it off.
Connect the mast winch line to the jib halyard with connectors or a simple easily removed knot.
Make sure all running and standing rigging is clear and ready to allow for the mast to rise.
Tension the mast winch to take the stretch out of the jib halyard.
I stand at the stern rail and assist the mast in its first couple of feet of rise to take some strain off the lines.
The second person starts winding up the winch as I walk along to keep an eye on things.
If any rigging is twisted or snagged, just stop cranking the winch and reverse it a couple of turns to ease it.
You can stop at any point in the raising to correct any issues.
Once the mast is vertical the winch will hold tension while the front stay is attached.
Release the winch pressure and disconnect the jib halyard and the main halyard.
Unclip the bridles and toss them in the lazarette.

Note:  In the video (our first time using the system) we found that we should have covered the roller furler drum with a towel or padded bag to keep it from scratching the topsides.


LOWERING
Re-attach the jib halyard.
Clip on the bridles and connect the main halyard.
Tension the main halyard.
Put some tension on the mast winch.
Remove the front stay clip.
Run the winch in reverse and slowly lower the mast.
Again I like to assist the mast the last couple of feet of drop to reduce the strain on the lines.
Unhook the jib halyard.
Leave the bridle hooked up and leave the main halyard attached as well.  Then it is ready for the next raising.

Com-Pac 23 Mast Raising Video

I'd like to make sure that I have properly stated that I didn't invent this system.  All I have done is take the parts of other similar systems and make my own version of it.

Monday, March 19, 2012

Driveway Sailing

The weather was right - in the 80's with lots of sunshine.  So we uncovered Wrinkles and tried stepping the mast for the first time.  However, Mike had to make a mast raising system first.  Mister Engineer quickly fabricated a pulley set-up that pulls the mast up (cranked by me) while he walks forward with the mast and furler.  Very simple and very slick!  He'll post more details.  My excitement is that we were able to raise the mast pretty easily, without any trouble and found out where all the pieces/parts go.   Not that much different from the 19.  We unrolled the jib and figured out those lines.  It was too windy to try raising the mainsail, besides we have ordered new halyards as the ones on the boat were sun-rotted.

My other job was to remove the name that was previously painted on.  This was truly a "rice krispie treat" moment (looks harder than what it really is).   We looked online and several people mentioned that they, as well as professionals,  used Easy Off Oven Cleaner.  (Note:  They said to use the non-lemon version).  So I taped off the area with painters tape and garbage bags and set to work anticipating the need for plenty of elbow grease.  I was pleasantly surprised.  After the foam worked for five minutes, all I had to do was go over the area with a damp towel and voila! no more name.  It took longer to tape off the area than it did to remove the paint!  There is still an underlying layer that Mike is going to have to compound or sand off, but as long as you don't look too closely, the name is gone!  We'll have to do an official renaming ceremony to please the sea gods.

The lakes are still very low, so we can't put the boat in the water - yet!  Close, we are so close!